Zen

Source string Source string

93/10000 · 93

The string is read only.

English Actions
Unselected and Selected Disk
Disk selection in the Installation Destination screen. Two disks are displayed; only the one on the right side will be used
anaconda/StorageSpoke_Selected.png
After you select all disks you want to install {PRODUCT}, select one of the two options in the `Other Storage Options` section:
`Automatically configure partitioning` - If this option is selected, then after you press `Done` in the top left corner of the screen, the installer will determine the total amount of space on all selected disks, and it will create a _Logical Volume Management_ (LVM) layout suitable for your system. The specifics of this layout depend on whether your system uses BIOS or UEFI firmware, the total amount of free space on your disks, and the amount of RAM on your system (which determines the size of your swap space).
With automatic partitioning, you can also select the `I would like to make additional space available` option below. Use this option if you want to reclaim space from an existing partitioning layout - for example, if a disk you want to use already contains a different operating system, and you want to make this system's partitions smaller to allow more room for {PRODUCT}. The `Reclaim space` dialog which opens if this option is selected is described later in this section.
`I will configure partitioning` - Select this option and press `Done` in the top left corner of the screen to configure your system's partitioning layout manually. This requires some knowledge of the theory behind disk partitions and related concepts, but gives you full control over the way the system will be installed. For instructions for manual partitioning, see xref:Installing_Using_Anaconda.adoc#sect-installation-gui-manual-partitioning[Manual Partitioning].
Additionally, you can select `Encrypt my data`pass:attributes[{blank}]; this will encrypt all partitions except the ones needed to boot the system (such as `/boot`) using _Linux Unified Key Setup_ (LUKS). Encrypting your hard drive is recommended. For detailed information about LUKS encryption, see the [citetitle]_{PRODUCT} Security{nbsp}Guide_, available at link:++http://docs.fedoraproject.org/++[].
If you lose the LUKS passphrase, any encrypted partitions and the data on them will become completely inaccessible. There is no way to recover a lost passphrase. However, if you perform a Kickstart installation, you can save encryption passphrases and create backup encryption passphrases during the installation. See xref:advanced/Kickstart_Installations.adoc#chap-kickstart-installations[Automating the Installation with Kickstart] for information about Kickstart installations.
To control which one of your selected storage devices will contain the _boot loader_, click the `Full disk summary and bootloader` link in the bottom left corner of the screen, and follow the instructions in xref:install/Installing_Using_Anaconda.adoc#sect-installation-gui-storage-partitioning-bootloader[Boot Loader Installation]. Note that while in most cases it is sufficient to leave the boot loader in the default location, some configurations (for example, systems which require _chain loading_ from another boot loader) will require the boot drive to be specified manually.
After you select storage devices, choose between automatic and manual partitioning, configure encryption and boot loader location, press `Done` in the top left corner of the screen. Then, depending on your settings, the following will happen:
If you chose to encrypt your hard drive, the `Disk Encryption Passphrase` dialog will appear. Enter your chosen passphrase into the `Passphrase` and `Confirm` fields. When you do so, the passphrase will be automatically evaluated and its strength will be displayed, along with suggestions on how to make it stronger if the installer has determined it to be weak. For information about creating strong passwords, see [citetitle]_{PRODUCT} Security{nbsp}Guide_.
If you selected automatic partitioning and the `I would like to make additional space available`, or if there is not enough free space on your selected hard drives to install {PRODUCT}, the `Reclaim Space` dialog will appear. This dialog lists all disk devices you have configured and all partitions on those devices. The bottom right corner of the dialog displays information about how much space the system needs for at least a minimal installation and how much space you have reclaimed.
If you use the `Reclaim Space` dialog to *delete* a partition, all data on that partition will be lost. If you want to preserve your data, use the `Shrink` option, not the `Delete` option.
First, review the displayed list of available storage devices. The `Reclaimable Space` column shows how much space can be reclaimed from each entry. To reclaim space, select a disk or partition, and press either the `Delete` button to delete that partition (or all partitions on a selected disk), or `Shrink` to use free space on a partition while preserving existing data. Alternatively, you can press `Delete all` in the bottom right corner; this will delete all existing partitions on all disks and make this space available to {PRODUCT}, but all existing data on all disks will be lost.
After you free enough space for your {PRODUCT} installation, press `Reclaim space` to finish.
No changes to any disks will be made until you press `Begin Installation` in xref:Installing_Using_Anaconda.adoc#sect-installation-gui-installation-summary[Installation Summary]. The `Reclaim Space` dialog only *marks* partitions for resizing or deletion, but no such action is performed immediately.
If you selected the `I will configure partitioning` option, pressing `Done` will open the `Manual Partitioning` screen. See xref:Installing_Using_Anaconda.adoc#sect-installation-gui-manual-partitioning[Manual Partitioning] for further instructions.

Loading…

User avatar None

String updated in the repository

  1. fedora-docs-l10n/fedora-install-guide
  2. f28/pages/_partials/install/StorageSpoke
  3. English
After you free enough space for your {PRODUCT} installation, press `Reclaim space` to finish.
After you free enough space for your {PRODUCT} installation, press `Reclaim space` to finish.
5 months ago
Browse all string changes

Things to check

Multiple failing checks

Following checks are failing:
Inconsistent: Finnish, Indonesian, Portuguese (Brazil), Turkish, Ukrainian, Chinese (Simplified)

Reset

Glossary

English English
No related strings found in the glossary.

String information

Source string description
type: Plain text
Flags
read-only
Source string location
./pages/_partials/install/StorageSpoke.adoc:76
String age
5 months ago
Last updated
5 months ago
Source string age
5 months ago
Translation file
pot/f28/pages/_partials/install/StorageSpoke.pot, string 27