fedora-docs-l10n/quick-docs/master/pages/firewalld — English @ Fedora Weblate: ● firewalld.service - firewalld

Source string Source string

English

● firewalld.service - firewalld - dynamic firewall daemon
     Loaded: loaded (/usr/lib/systemd/system/firewalld.service; enabled; preset>
    Drop-In: /usr/lib/systemd/system/service.d
             └─10-timeout-abort.conf
     Active: active (running) since Sat 2023-08-19 19:05:18 CEST; 3 days ago
     ...

Needs editing

The string is read only.

Skip

	English	Actions
	A _firewall_ is a way to protect machines from any unwanted access from outside. In Fedora, it is installed by default during the installation of the operating system, enabled and configured to provide secure operation even without any additional action by the administrator. It blocks any access other than ssh by default.
	How it works
	A firewall enables users to control incoming network traffic on host machines by defining a set of _firewall rules_. These rules are used to sort the incoming traffic and either block it or allow through.
	`firewalld` is a firewall service daemon that provides a dynamic customizable host-based firewall with a `D-Bus` interface. Being dynamic, it enables creating, changing, and deleting the rules without the necessity to restart the firewall daemon each time the rules are changed.
	`firewalld` uses the concepts of _zones_ and _services_, that simplify the traffic management.
	`_Zones_` are predefined sets of rules. Network interfaces and sources can be assigned to a zone. The traffic allowed depends on the network your computer is connected to and the security level this network is assigned. Firewall services are predefined rules that cover all necessary settings to allow incoming traffic for a specific service and they apply within a zone.
	`_Services_` use one or more ports or addresses for network communication. Firewalls filter communication based on ports. To allow network traffic for a service, its ports must be open. `firewalld` blocks all traffic on ports that are not explicitly set as open. Some zones, such as trusted, allow all traffic by default.
	Additional resources
	For more information about using firewalld and configuring zones and services, see link:https://firewalld.org/documentation/[firewalld documentation] or link:https://fedoraproject.org/wiki/Firewalld[Fedora wiki:firewalld]
	Setting up firewalld
	All Fedora Editions install, configure and activate the firewall by default. No further action is required. The only exception is _Cloud Edition_, which relies on the higher level cloud system.
	Some third party variations and redistributions may differ. In this case, it is up to the administrator to install and activate the firewall afterwards.
	You check if firewalld is set up in a terminal by issuing
	systemctl status firewalld
	You should get soemething like
	● firewalld.service - firewalld - dynamic firewall daemon Loaded: loaded (/usr/lib/systemd/system/firewalld.service; enabled; preset> Drop-In: /usr/lib/systemd/system/service.d └─10-timeout-abort.conf Active: active (running) since Sat 2023-08-19 19:05:18 CEST; 3 days ago ...
	Installing and activating firewalld
	In case you get by the command above something like
	Unit firewalld.service could not be found.
	you have to install it. Run on the command line:
	$ sudo dnf install firewalld $ sudo systemctl unmask firewalld $ sudo systemctl start firewalld $ sudo systemctl enable firewalld
	This sequence installs, starts and ensures an automatic restart after a system boot.
	Adjusting firewalld operations during system maintenance
	Sometimes a system administrator has to stop or restart firewalld during system maintenance tasks.
	Stop firewalld
	$ sudo systemctl stop firewalld
	Prevent autostart at system boot
	$ sudo systemctl disable firewalld
	Start firewalld
	$ sudo systemctl start firewalld
	Activate autostart at system boot

Loading…

None

String updated in the repository

English

English 309 characters edited Current translation Read only

a year ago

Browse all string changes

Things to check

Ellipsis

The string uses three dots (...) instead of an ellipsis character (…)

Reset

Glossary

English	English
No related strings found in the glossary.

String information

Source string description

type: delimited block -

Flags

no-wrap, read-only

Source string location

./pages/firewalld.adoc:51

String age

a year ago

Last updated

a year ago

Source string age

a year ago

Translation file

pot/master/pages/firewalld.pot, string 18

Shortcut	Action
`?`	Open available keyboard shortcuts.
`Alt` + `Home`	Navigate to the first translation in the current search.
`Alt` + `End`	Navigate to the last translation in the current search.
`Alt` + `PageUp` or `Ctrl` + `↑` or `Alt` + `↑` or `Cmd` + `↑` or	Navigate to the last translation in the current search.
`Alt` + `PageDown` or `Ctrl` + `↓` or `Alt` + `↓` or `Cmd` + `↓` or	Navigate to the next translation in the current search.
`Ctrl` + `Enter` or `Cmd` + `Enter`	Submit current form; this works the same as pressing Save and continue while editing translation.
`Ctrl` + `Shift` + `Enter` or `Cmd` + `Shift` +`Enter`	Unmark translation as Needing edit and submit it.
`Alt` + `Enter` or `Option` + `Enter`	Submit the string as a suggestion; this works the same as pressing Suggest while editing translation.
`Ctrl` + `E` or `Cmd` + `E`	Focus on translation editor.
`Ctrl` + `U` or `Cmd` + `U`	Focus on comment editor.
`Ctrl` + `M` or `Cmd` + `M`	Shows Automatic suggestions tab.
`Ctrl` + `1` to `Ctrl` + `9` or `Cmd` + `1` to `Cmd` + `9`	Copies placeable of a given number from source string.
`Ctrl` + `M` followed by `1` to `9` or `Cmd` + `M` followed by `1` to `9`	Copy the machine translation of a given number to current translation.
`Ctrl` + `I` followed by `1` to `9` or `Cmd` + `I` followed by `1` to `9`	Ignore one item in the list of failing checks.
`Ctrl` + `J` or `Cmd` + `J`	Shows the Nearby strings tab.
`Ctrl` + `S` or `Cmd` + `S`	Focus on search field.
`Ctrl` + `O` or `Cmd` + `O`	Copy the source string.
`Ctrl` + `Y` or `Cmd` + `Y`	Toggle the Needs editing checkbox.
`→`	Browse the next translation string.
`←`	Browse the previous translation string.