fedora-docs-l10n/fedora-install-guide/f29/pages/install/Troubleshooting — Turkish @ Fedora Weblate: mem=pass:attributes[{blank}]_xx

Translation

English

type: delimited block -

Turkish

Needs editing

Skip

	English	Turkish	Actions
	For additional information about [command]#df# and an explanation of the options available (such as the [option]#-h# option used in this example), see the `df(1)` man page.
	Is Your RAM Not Being Recognized?
	In some cases the kernel does not recognize all of your memory (RAM), which causes the system to use less memory than is installed. You can find out how much RAM is being utilized using the [command]#free -m# command. If the displayed total amount of memory does not match your expectations, it is likely that at least one of your memory modules is faulty. On BIOS-based systems, you can use the [application]Memtest86+ utility to test your system's memory - see xref:advanced/Boot_Options.adoc#sect-boot-options-memtest[Loading the Memory (RAM) Testing Mode] for details.
	If you have 4GB or more memory installed, but {PRODUCT} only shows around 3.5GB or 3.7GB, you have probably installed a 32-bit version of {PRODUCT} on a 64bit kernel. For modern systems, use the 64-bit (x86_64) version.
	Some hardware configurations have a part of the system's RAM reserved and unavailable to the main system. Notably, laptop computers with integrated graphics cards will reserve some memory for the GPU. For example, a laptop with 4{nbsp}GB of RAM and an integrated Intel graphics card will show only roughly 3.7{nbsp}GB of available memory, even with a 64-bit system.
	Additionally, the [application]kdump crash kernel dumping mechanism reserves some memory for the secondary kernel used in case of the primary kernel crashing. This reserved memory will also not be displayed as available when using the [command]#free# command. For details about [application]kdump and its memory requirements, see the [citetitle]_{PRODUCT} System Administrator's Guide_, available at link:++https://docs.fedoraproject.org/++[].
	If you made sure that your memory does not have any issues, you can try and set the amount of memory manually using the [option]#mem=# kernel option.
	Configuring the Memory Manually
	Start your computer and wait until the boot loader menu appears. If you set your boot loader timeout period to 0, hold down the kbd:[Esc] key to access it.
	When the boot loader menu appears, use your cursor keys to highlight the entry you want to boot and press the kbd:[e] key to edit this entry's options.
	In the list of options, find the kernel line - that is, the line beginning with the keyword `linux` (or, in some cases, `linux16`). Append the following option to the end of this line:
	mem=pass:attributes[{blank}]_xx_pass:attributes[{blank}]M
	Replace _xx_ with the amount of RAM you have in megabytes.
	Press kbd:[F10] or kbd:[Ctrl + X] to boot your system with the edited options.	Düzenlenen seçeneklerle sisteminizi önyüklemek için kbd:[F10] veya kbd:[Ctrl + X] tuşlarına basın.
	Wait for the system to boot and log in. Then, open a command line and execute the [command]#free -m# command again. If total amount of RAM displayed by the command matches your expectations, append the following to the line beginning with `GRUB_CMDLINE_LINUX` in the `/etc/default/grub` file to make the change permanent:
	mem=pass:attributes[{blank}]_xx_pass:attributes[{blank}]M	mem=pass:attributes[{blank}]_xx_pass:attributes[{blank}]M
	Replace _xx_ with the amount of RAM you have in megabytes.	_xx_ değerini megabayt cinsinden sahip olduğunuz RAM miktarıyla değiştirin.
	After you updated the file and saved it, refresh the boot loader configuration so that the change will take effect. Run the following command with root privileges:
	# grub2-mkconfig --output=/boot/grub2/grub.cfg	# grub2-mkconfig --output=/boot/grub2/grub.cfg
	In `/etc/default/grub`, the above example would look similar to the following:
	GRUB_TIMEOUT=5 GRUB_DISTRIBUTOR="$(sed 's, release.*$,,g' /etc/system-release)" GRUB_DEFAULT=saved GRUB_DISABLE_SUBMENU=true GRUB_TERMINAL_OUTPUT="console" GRUB_CMDLINE_LINUX="rd.lvm.lv=rhel/root vconsole.font=latarcyrheb-sun16 rd.lvm.lv=rhel/swap $([ -x /usr/sbin/rhcrashkernel.param ] && /usr/sbin/rhcrashkernel-param \|\| :) vconsole.keymap=us rhgb quiet mem=1024M" GRUB_DISABLE_RECOVERY="true"
	See the [citetitle]_{PRODUCT} System Administrator's Guide_, available at link:++https://docs.fedoraproject.org/++[], for more information about working with the [application]GRUB2 boot loader.

Loading…

None

String updated in the repository

English

Turkish 59 characters edited Current translation Translated

3 months ago

Browse all string changes

Things to check

Unchanged translation

Source and translation are identical

Reset

Glossary

English	Turkish
No related strings found in the glossary.

String information

Source string description

type: delimited block -

Flags

no-wrap

Source string location

./pages/install/Troubleshooting.adoc:422

String age

3 months ago

Last updated

3 months ago

Source string age

3 months ago

Translation file

po/tr/f29/pages/install/Troubleshooting.po, string 150